X
X
X

The History and Importance of Stone Milling

Since the third century B.C., the process of milling grains into flour consisted of passing whole grains through two large moving millstones. Traditionally, one of the stones turned (the runner stone) via water, animal or human power source, while the other (the bed stone) remained stationary. This method crushes the grains but keeps all the parts of the grain (the germ, bran and endosperm) intact. Millstones grind at a slow rate, so the friction only produces a low heat, which keeps the germ fat from oxidizing and becoming rancid, which can destroy some of the nutrients inherent in the grain.

Stone milling was the norm throughout history until around the 19th century. As times and cooking practices changed, it was found that stone milling didn’t produce flour that was fine enough for making pastries. Stone milling also produces a nutty flavor and texture that consumers were finding less than ideal for some of their recipes. Millstones also wear down after use, and have to be “dressed” or sharpened about every 90 days or so, creating concern that corundum dust from the grinding stones became part of the flour being produced. These concerns, plus the growing demand for flour vs. the slow production time of stone mills, led to the development of a faster alternative to stone milling, called roller milling.

The roller milling, or “high grinding” method slowly replaced most existing traditional stone mills. With roller milling, steel rollers quickly explode the grain over a series of passes through the mill. The reground flour is thoroughly sifted to remove the bran and germ, thereby also removing some of the nutrients. The friction of the roller milling process also produces higher temperature flour, which is reported to affect the nutrients as well. According to a publication by the Ecological Agriculture Projects, “heat causes the fat from the germ portion to oxidize and become rancid and much of the vitamins to be destroyed” (Aubert, 1989). Similarly, the Flour Milling, Baking and Confectionery Technology Department at the Central Food Technological Research Institute found that some loss of essential fatty acid and amino acids occurs at milling temperatures above 170°F.

The roller milling process produces flour that is whiter than traditional dark-colored, nutrient-rich, stone ground flour. Upon its introduction, the lighter color appealed to consumers, particularly the wealthy, and so white flour became desirable to all, even though it was less nutritious. With its ability to be produced faster in order to meet growing consumer demand, white flour eventually dominated the market.

Certainly, millers knew that nutrients were being lost in the process, which led to the development of enriched flour, where synthetic vitamins and minerals are added to the flour after milling. Of course, synthetic is never the same as the real thing. Which raised the question, what effect would this flour have on people’s health over time? The responses to that question called for change.

In the 1920s, the Food and Drug Administration’s Dr. Harvey Wiley attempted to ban refined, bleached white flour due to how it was made and the resulting loss of nutrition. In that same decade, engineer and nutritionist Dr. Royal Lee was beginning to take his own action against the process of commercial milling by developing a household mill that made the full nutrition of whole grains possible again.

By 1950, Dr. Lee’s mill was available to consumers. Using an air current to propel grains against a stationary corundum stone, Dr. Lee’s mill was able to produce a flour fine enough for pastry, while retaining all the nutritional value of whole grains. According to Lee and other nutritionists, milling by stone, in the amount needed for immediate use, is the only way to retain the complete grain and it’s nutrients, which include dietary fiber, phosphorus, thiamin, niacin, and B6. The Ecological Agriculture Projects paper also states, “The nutritional importance of using fresh stone-ground grains for bread-making was revealed in the results of feeding studies in Germany (Bernasek, 1970).”

Prices for household stone mills start at around $600 and can range to over $1000. The stone, technology, accompanying parts and country of manufacturing are all factors in the cost. Mills priced below that range use metal burrs instead of stone. These burrs shred or cut the grain, produce higher temperature flour due to friction, and don’t offer the nutritional and other benefits of stone referred to in this article.

The history of stone milling is an interesting look at the economy’s affect on nutrition. Fortunately, there is now a growing movement to go back to the stone milling methods that provide people the nutrition they need.

 

Back To News